Free shipping on orders $35+ · $5.99 under $35 · Ships from New Jersey

Contact Cleaners, Enhancers & Fader Lubes

Electrical contact cleaner restores switches, jacks, connectors and controls that crackle, cut out or show high resistance. This collection is organized by job: DeoxIT D-series cleans and deoxidizes metal contacts, DeoxIT Gold conditions plated contacts, FaderLube and FaderGrease treat conductive-plastic faders and potentiometers, and Super Lube connector gel and dielectric grease seal terminals against moisture. Match the product to the contact material and to how you can reach it: a spray to flush, a needle or brush for precise work. Aerosols ship by ground to the contiguous US only.

Showing all 14 results

How to choose: match the product to the job

Symptom or jobContact typeProductFormat
Crackling jack, intermittent switch, oxidized connectorMetal contactsDeoxIT D5S-6, DN5S-6N, D100L-25C5% spray or 100% liquid
New, clean or gold-plated connectors; critical contactsPlated metalsDeoxIT Gold G5S-65% spray
Scratchy fader or slide potentiometerConductive plastic, carbonFaderLube F5S-H6 or F100L-L25CSpray or needle
Fader feels loose and needs dampingSliding plastic and metal surfacesFaderGrease DFG-213-8G8 g syringe
Battery terminals, exposed plugs, bulb socketsConnections exposed to moistureSuper Lube 82003 gel or 91003 dielectric grease3 oz tube

Where contact cleaner helps

  • Audio gear: guitar and amplifier jacks, potentiometers, mixer faders and patch bays
  • Computers and communication equipment: sockets, edge connectors and cable ends
  • Automotive, RV and marine electrical systems
  • Avionics, medical, security and photography equipment, all named in CAIG's application lists

How to apply (CAIG's directions)

  1. Turn the device off and unplug it.
  2. Apply one short burst of spray, or a small amount of 100% liquid with the needle or brush, to the contact surface.
  3. Operate the switch, plug or control to break up oxides, wait a few seconds, then apply a second short burst.
  4. Wipe off the excess, leaving the thin coat CAIG recommends, and wait two minutes before turning the equipment on.

Frequently asked questions

Is contact cleaner safe on plastic?

DeoxIT is formulated to be safe on most plastics, but test first. CAIG rates D100L excellent on ABS, nylon, polycarbonate, polypropylene, PTFE and PVC and poor on TPE, rubber and varnish, and warns that stressed acrylic, ABS or polycarbonate may craze. With the solvent sprays, test aging ABS on vintage gear first.

Which product is right for potentiometers?

It depends on the track. Conductive-plastic and carbon controls take FaderLube (F5S-H6 or F100L-L25C), while metal-contact switches, jacks and connectors take the D-series; CAIG says the F-series is not for metal contacts and connectors.

Contact cleaner or isopropyl alcohol?

Alcohol cleans and evaporates without lubricating or protecting the surface. DeoxIT D-series is a contact rejuvenator that deoxidizes and leaves a thin protective, lubricating film, so it suits contacts where oxidation is causing the fault.

Is there a non-flammable contact cleaner?

Yes. DeoxIT DN5S-6N is a non-flammable spray, and the 100% liquid applicators are non-flammable too. D5S-6, G5S-6 and F5S-H6 are extremely flammable aerosols, so use them away from heat and sparks.

Related: DeoxIT D-series contact treatment guide, DeoxIT F-series fader guide, dielectric grease for connectors and every DeoxIT part number. CAIG safety data sheets are in our Technical & Safety Data Sheets library.

Guides

Scroll to Top